Yamatake HGC303 Скачать руководство пользователя страница 106

Страница: 106 / 130

Operation

Yamatake Corporation

3-64

Model HGC303 - Heat Value Gas Chromatograph

Chromatogram

Figure 3-25 Trend Chromatogram (online)

* In case of Windows 98 or Me, data are also saved in C:\My documents\MyHGC.

Table 3-31 Chromatogram description

No.

Display

Description

URV

Upper Range Value for vertical axis

Click on the URV button to change the URV value

Default value is 1

Load (Offline)

Saved data is recalled. File name extension: .cg1

Save (Online)

The latest data is saved.

Default directory is “C:\Program files\hgm\data”.*

Verify that your printer is connected and working properly.

Over write

Overlapped Chromatograms are displayed.

Reverse

Click on the reverse button to invert the display and [No.9] [Forward]

changes the display to [Reverse].

Default: [Forward]

LRV

Lower Range Value for vertical axis

Click on the LRV button to change the LRV value.

Default value: -1

Disp Components

Check the box to display each component name.

Forward-Reverse

To invert / revert the display

Upper gate marker

Gate start marker of each component.

Lower gate marker

Gate end marker of each component.

Time

Online: Date and time when latest data is reloaded

Offline: Saved date and time

Status bar (Online)

Online: Date and time of the latest data (data is reloaded every 5 min.)

Offline: Date and time of when the data was saved.

1
2
3

7
8

Содержание HGC303



































































































































Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды

Yamatake HGC303, Руководство пользователя

Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды