manualshive.com logo in svg

Wintriss Shadow VI, Руководство пользователя

Пользовательский руководство Wintriss Shadow VI доступен для бесплатной загрузки с manualshive.com. Получите все необходимые инструкции и рекомендации для использования этого продукта. Узнайте, как максимально эффективно использовать Wintriss Shadow VI, загрузив руководство сейчас!

Поделиться
Скачать
background image

Shadow VI User Manual 

1107200 

Table of Contents 

 

page iii 

At the Optic Heads...............................................................................................................................80

 

At the Control ......................................................................................................................................80

 

Inside the Control.................................................................................................................................81

 

External MPCE Monitoring: Checking DS5 and DS6.........................................................................85

 

Shadow VI Optic Head Connector ...........................................................................................................86

 

Checking and Cleaning Lens Window(s).................................................................................................87

 

Checking Alignment.................................................................................................................................87

 

Alignment Problem or Bad Phototransistor .........................................................................................87

 

Checking and Replacing Fuses.................................................................................................................88

 

Checking and Replacing Control Relays..................................................................................................89

 

If the Relay Has Failed Completely .....................................................................................................89

 

Checking Relays with a Voltmeter ......................................................................................................90

 

Replacing Safety Relays ......................................................................................................................91

 

Checking and Correcting Cross Talk........................................................................................................92

 

Appendix A – Extracts from OSHA Regulations and ANSI Standards ......... 93

 

Extracts from OSHA Regulation 1910.217 ..............................................................................................93

 

Extracts from ANSI Standards for Presence-sensing Devices .................................................................97

 

Daily Tests in English ............................................................................................................................113

 

Tests Quotidiens du Rideau de Lumiere.................................................................................................114

 

Daily Tests in French..............................................................................................................................114

 

Appendix B – Shadow VI Panel Mount.......................................................... 115

 

Standard Enclosure Versus Optional Panel Mount ................................................................................115

 

Preparation for Mounting Shadow Using Your Enclosure.....................................................................115

 

About Shadow VI Panel Mount Labels .............................................................................................116

 

Appendix C – Installation of Shadow VI-WPC Control Board ..................... 119

 

Mounting Dimensions and Required Clearance .....................................................................................119

 

About Shadow VI-WPC Control Board Labels.................................................................................120

 

Wiring Shadow VI optic heads to the board ..........................................................................................124

 

Connecting AC wiring to WPC ..............................................................................................................125

 

Connecting Stop Circuits to WPC ..........................................................................................................126

 

Making settings on the control board .....................................................................................................127

 

Floating window setting.....................................................................................................................127

 

J12 Setting..........................................................................................................................................128

 

Reset button ............................................................................................................................................129

 

Appendix D – Replacement Parts.................................................................. 131

 

Index ................................................................................................................ 133

 

Wintriss Manuals ............................................................................................ 137

 

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Accent DUO Assembly Manual preview
DUO
Бренд: Accent Страницы: 2
80/20 Xtreme DIY Assembly Instructions Manual preview
Xtreme DIY
Бренд: 80/20 Страницы: 6
GALA MEBLE G60 Assembly Manual preview
G60
Бренд: GALA MEBLE Страницы: 13
Walker Edison D51L29 Assembly Instructions Manual preview
D51L29
Бренд: Walker Edison Страницы: 10
Quelle 693326 Assembly Instructions Manual preview
693326
Бренд: Quelle Страницы: 13
Quax JOY Desk with drawer and door 54 06 11 Series Manual preview
JOY Desk with drawer and door 54 06 11 Series
Бренд: Quax Страницы: 41
PATIOJOY OP71263 Manual preview
OP71263
Бренд: PATIOJOY Страницы: 9
Argos Gabe Instruction Manual preview
Gabe
Бренд: Argos Страницы: 8
Cooper Lighting Portfolio 846 Specification Sheet preview
Portfolio 846
Бренд: Cooper Lighting Страницы: 2
Target 6-Cube Assembly Instructions Manual preview
6-Cube
Бренд: Target Страницы: 20
Cattelan Italia Atelier Assembling Instructions preview
Atelier
Бренд: Cattelan Italia Страницы: 12
Poliman Branco/Preto - 539.7 Assembling Instructions preview
Branco/Preto - 539.7
Бренд: Poliman Страницы: 2
Dawn Qubo Series Installation Manual preview
Qubo Series
Бренд: Dawn Страницы: 11
Next CORSICA 664566 Assembly Instructions Manual preview
CORSICA 664566
Бренд: Next Страницы: 16
Triarch 32321/16 Instructions preview
32321/16
Бренд: Triarch Страницы: 1
Forte SXKS721R Assembling Instruction preview
SXKS721R
Бренд: Forte Страницы: 24
KLOBER cat97 Operating Instructions Manual preview
cat97
Бренд: KLOBER Страницы: 40
Amish Tables Double Pedstal Style Table Assembly Instructions preview
Double Pedstal Style Table
Бренд: Amish Tables Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды