Wintriss Shadow VI Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 159

background image

Shadow VI User Manual

1107200

Installation and Checkout

Chapter 2

page 67

1. Have ready 1-1/4" (32 mm) and 1/8” (3.2 mm) opaque test bars. If your light curtain has

floating window, also have ready a 2” (50.8 mm) opaque test bar. Turn on power to
Shadow safety light curtain and to the machine.

2. Make sure the floating window option has been disabled, if your light curtain has it, by

setting the "floating window" switch at switch block S1 (in the control) to the “OFF”
position (see “Making Settings Inside the Control,” page 59).

NOTICE

LIGHT CURTAINS EQUIPPED WITH FLOATING WINDOW OPTION

Indicators on the receiver and on the control blink to indicate that floating window has been

enabled. This indicator should be off when you perform this checkout procedure with the 1
¼” test bar. Later you will enable floating window and repeat the test with the 2” bar .

3. Using the 1-1/4" (32 mm) diameter test bar, interrupt the sensing field on the receiver

side by passing the test bar from the top to the bottom of the receiver's lens cover. The
red light should come on while the test bar is in the sensing field.

4. Repeat step 3, passing the 1-1/4" (32 mm) diameter test bar from the top to the bottom of

the transmitter's lens cover. The red light should stay on while the test bar is in the
sensing field.

5. Block the light curtain so that the red light is on; verify that the machine will not start

while the light curtain is obstructed.

6. Using the 1/8” (3.2 mm) diameter test bar, interrupt the sensing field on the receiver side

by passing from the top to the bottom of the receiver’s lens cover. The green light
should remain on. If the red light comes on, realign the heads to prevent nuisance stops.

7. Repeat step 6, passing the 1/8” diameter test bar from the top to the bottom of the

transmitter’s lens cover. The green light should remain on. If the red light comes on,
realign the heads to prevent nuisance stops.

NOTICE

If muting is used, interrupting the light curtain during the non-hazardous portion of the stroke

(upstroke) will not stop the machine. To test, you must interrupt the stroke on the
downstroke, which is the hazardous portion of the stroke.

8. Start the machine and interrupt the light field with the 1-1/4" (32 mm) diameter test bar.

The red indicator light on the receiver should come on and the machine should stop
immediately.

NOTICE

Step 9 applies specifically to presses with single cycle and cycle stop capability. If you

cannot single stroke or top stop your press, carry out all steps except Step 9. You must
ensure that your Shadow meets the requirements of the other steps before using the
Shadow-equipped equipment. Remember, your press must be able to stop when the light
beam is broken.

«
...
77
78
79
80
81
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: NABBI Страницы: 23

Tenera Auto-Lift

Бренд: Lafayette Страницы: 3

Бренд: garofalo Страницы: 12

Бренд: ShadeLab Страницы: 32

Бренд: Walker Edison Страницы: 10

Бренд: WIEMANN Страницы: 5

Diag Corner Larder

Бренд: Wren Kitchens Страницы: 12

Standregal 1320

Бренд: Ticaa Страницы: 7

Бренд: White Страницы: 20

Бренд: Wenger Страницы: 4

Бренд: JAB Страницы: 28

24/7 ELITE 54666

Бренд: Office Star Products Страницы: 2

Бренд: aspenhome Страницы: 2

Бренд: Habitat Страницы: 12

Motific MOF24 Series

Бренд: ESI Страницы: 4

Fairford 803 622 07

Бренд: John Lewis Страницы: 10

Бренд: Wisteria Lane Страницы: 6

Бренд: Quax Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды