Wintriss Shadow VI Скачать руководство пользователя страница 100

Страница: 100 / 159

1107200

Shadow VI User Manual

page 88

Chapter 4

Troubleshooting Shadow VI

Checking and Replacing Fuses

WARNING

ELECTRIC SHOCK HAZARD

•

Ensure that the power source is off before checking or replacing fuses.

•

Disconnect power from the machinery it is connected to before making any wiring

connections. This includes disconnecting power to the machine control and motor.

•

Ensure that all procedures are performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

Any time Shadow loses power or will not allow press operation, first check the fuses that are
located in the control. They are easy to check and replace.

The fuses are common 3AG glass cartridge fuses (

1/4

" dia. x 1

1/4

" length) listed in Appendix

D. The rating,

1/4

amp and 4 amp, is marked next to the fuse on the circuit board. Here is

how to check the fuses inside the control.

1. Turn off power to Shadow.

Never check or change fuses with the power on.

2. Open the hinged cover of the control by loosening the locking screws.

3. Locate the fuses on the circuit board. Refer to the location of components illustration in

Chapter 2. There are 4 fuses - 1 power (at F1), 2 stop (at location F2 and F3), and 1
status (at F4).

4. Remove the plastic cover over the fuse. Look to see if the metallic strip inside any of the

fuses is broken. Test with an ohmmeter if available. Put the ohmmeter leads on each side
of the fuse. No resistance (0 ohms) means the fuse is good.

5. If the fuse has blown, pop it out of the holder by prying it out at the ends. Snap in a new

fuse.

6. Replace all plastic fuse covers.

WARNING

ELECTRIC SHOCK HAZARD

Replace plastic fuse covers after checking or replacing fuses. These covers help reduce the

risk of electric shock.

Failure to comply with these instructions could result in death or serious injury.

7. Close the control. Insert and tighten the locking screws.

Содержание Shadow VI
































































































































































Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды

Wintriss Shadow VI, Руководство пользователя

Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды