Wintriss Shadow VI Скачать руководство пользователя страница 103

Страница: 103 / 159

Shadow VI User Manual

1107200

Troubleshooting Shadow VI

Chapter 4

page 91

Replacing Safety Relays

DANGER

IMPROPER SAFETY RELAY REPAIR

Replace the Shadow VI Control board before placing the safety product back into operation

after the occurrence of a failed relay.

Failure to comply with these instructions will result in death or serious injury.

WARNING

ELECTRIC SHOCK HAZARD

•

Ensure that the power source is off before you make any wiring connections.

•

Disconnect power from the machinery it is connected to before making any wiring

connections. This includes disconnecting power to the machine control and motor.

•

Ensure that all procedures are performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

1. Turn off power to the Shadow VI control.

CAUTION

DAMAGE TO BOARD FROM STATIC DISCHARGE

Ground yourself before touching circuit boards or chips by touching a large metal object

such as the press. Static electricity can destroy electronic components.

Failure to comply with these instructions could result in property damage.

2. Making sure that you are grounded, open the Shadow VI enclosure (see Figure 2-13,

page 43).

3. Identify all cables with inputs on the Shadow VI Control board by the terminal block to

which they connect (see Figure 2-14, page 44) and attach identifying labels.

4. Remove cable connectors from terminal blocks.

5. Unscrew the old Shadow VI Control board from its mounting studs and remove it from

the enclosure.

6. Maintaining the orientation of the old board, place the new Shadow VI Control board on

the mounting studs and screw down.

CAUTION

The cable connector can be inserted into the terminal block in only one direction. Do

not try to force the connector into the terminal block; otherwise, you may damage one or
both components.

Failure to comply with these instructions could result in property damage.

7. Replace cable connectors in the appropriate terminal blocks, referring to the labels you

created in step 3.

Содержание Shadow VI
































































































































































Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды

Wintriss Shadow VI, Руководство пользователя

Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды