Wintriss Shadow VI Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 159

background image

1107200

Shadow VI User Manual

page 106

Appendix A

Excerpts from OSHA Regulations and

ANSI

Standards

Daily Tests in French and English

Extracts from ANSI B11.19-2003 8.3

Standards Requirements

Explanatory Information

8.3.1.5

The presence-sensing device shall

incorporate visual means to indicate that the
device is detecting an individual within the
effective sensing field of the device.

E8.3.1.5

Indicators (usually red and green),

displays or meters should be provided to
indicate the status of the device. The visual
means may be integral to the device or part of
the interface or machine control system.

Due to the prevalence of color blindness,
methods such as unambiguous positioning,
patterning, labeling or flashing of the indicators
may be effective in providing the indication
required.

8.3.1.6

The presence-sensing device shall

have a maximum response time that shall not
be affected by object sensitivity or
environmental changes.

The safeguarding supplier shall provide the
maximum response time of the presence-
sensing device.

8.3.1.7

The RF (radio frequency) presence-

sensing device shall provide means to adjust
the sensitivity of the field. The field, once
adjusted, shall not decrease in sensitivity below
this established level.

8.3.1.8

The electro-optical device shall not be

affected by ambient light conditions or by
changes in the device light source
characteristics, such that an increase in
response time or object sensitivity occurs.

E8.3.1.8

When the electro-optical device is

exposed to signals from other electro-optical
devices or to changes in ambient light
commonly associated with windows, light
fixtures, skylights, bay doors or work area
lights, the response time or object sensitivity
should not be adversely affected.

8.3.1.9

Components, subassemblies or

modules of electro-optical, RF, and area
scanning presence-sensing safeguarding
devices shall be designed and constructed to
meet the requirements of 6.1.

«
...
116
117
118
119
120
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Capitola SEA8031-Q

Бренд: Safavieh Furniture Страницы: 2

Бренд: Naomi Kids Страницы: 10

Бренд: Pessotto Страницы: 34

Бренд: StandDesk Страницы: 9

Lytecel LCS6G20LW132

Бренд: Lightolier Страницы: 2

Бренд: VIPACK Страницы: 8

Kosa Combo Changer/Dresser

Бренд: Oggi Страницы: 19

Бренд: East West Furniture Страницы: 5

Бренд: Guidecraft Страницы: 6

Schuhschrank 3025

Бренд: Germania Страницы: 12

TRESANTI EC6449LS22

Бренд: Twin-Star International Страницы: 12

ELODIE SB 19021-S5V

Бренд: emob Страницы: 5

Бренд: GALA MEBLE Страницы: 13

Бренд: Invacare Страницы: 12

Бренд: CorLiving Страницы: 12

JOSEPHINE 941242

Бренд: Next Страницы: 9

MANUEL H1000011507

Бренд: Ticaa Страницы: 11

Бренд: OCC Outdoors Products Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды