Wintriss Shadow VI Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 159

background image

Shadow VI User Manual

1107200

Troubleshooting Shadow VI

Chapter 4

page 89

Checking and Replacing Control Relays

DANGER

!

IMPROPER SAFETY RELAY REPAIR

•

Replace the Shadow VI Control board before placing the safety product back into operation

after the occurrence of a failed relay.

If a relay fuses

•

DO NOT reset the Shadow to restart the machine.

•

Remove the Shadow from operation immediately and replace the Shadow VI Control board

before operating the press again.

Failure to comply with these instructions will result in death or serious injury.

WARNING

!

ELECTRIC SHOCK HAZARD WHEN WORKING INSIDE ENCLOSURE WITH POWER ON

•

DO NOT touch electrical connections or circuit boards.

•

Use test equipment only on the terminals specified in the instructions.

•

Ensure that this test is performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

WARNING

!

ELECTRIC SHOCK HAZARD WHEN CHECKING OR REPLACING RELAYS

•

Turn off and disconnect power from the Shadow safety light curtain and from the machinery

it is connected to before checking relays or replacing the Shadow VI Control board unless
the test requires power to be on. This includes disconnecting power to the machine control
and motor.

•

Ensure that all tests and repairs are performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

If the Relay Has Failed Completely

If a relay has failed completely (will not energize to close contacts or the contacts are welded
shut), Shadow immediately stops the machinery and will not allow further press operation.
The red light will always be on.

In this case, you cannot check relay contacts with a voltmeter (see next section). This is
because Shadow will not allow relay operation if a relay failure occurs. Even the contacts of
the good relay will be open and all voltages will be zero. You must replace the Shadow VI
control board (see

Replacing Safety Relays

«
...
99
100
101
102
103
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: MAJA Möbel Страницы: 14

Бренд: Takara Belmont Страницы: 24

SHELF CLASS BRUNO BOOKSHELF

Бренд: Dutch BONE Страницы: 3

Бренд: Elle Decor Страницы: 8

Бренд: HELD MOBEL Страницы: 3

Emily Coffee Table

Бренд: Zest 4 Leisure Страницы: 3

Бренд: Home Decorators Collection Страницы: 12

Бренд: Walker Edison Страницы: 8

ZEFIR 3276007182972

Бренд: Naterial Страницы: 116

Бренд: J&K Страницы: 9

Бренд: Sable Страницы: 24

Habitat 939/7673

Бренд: Argos Страницы: 7

Бренд: Quax Страницы: 20

Бренд: Quoizel Страницы: 2

Бренд: CLEAR DESIGN Страницы: 24

Бренд: Multimo Страницы: 20

Junior Whittington L4983

Бренд: Great Little Trading Страницы: 5

2 Door TV Cabinet

Бренд: Arlo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды