Wintriss Shadow VI Скачать руководство пользователя страница 3

Страница: 3 / 159

Changes for Revision E of the

Shadow VI User Manual

(1107200)

This revision of the Shadow VI Safety Light Curtain User Manual covers Shadow VI models
with response times of 30 to 40 ms, maximum.

The changes include:

•

The Remote Interrupt button has been removed from the Shadow VI Control board (see

page 44) , and, as a result, all references to the button have been removed from the
manual.

•

AC power is now grounded to the set screw terminal on the Shadow VI enclosure rather

than to pin #3 on TB 1 (see page 51).

•

The procedure for replacing Shadow VI safety relays has been updated. Instead of

replacing individual relays in the event of a relay failure, you now must replace the
Shadow VI Control board. See page 91.

•

References to and excerpts from ANSI standards B11.1 and B11.19 have been updated to

their current versions, B11.1-2009 and B11.19-2003. See Appendix A.

Содержание Shadow VI
































































































































































Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды

Wintriss Shadow VI, Руководство пользователя

Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды