manualshive.com logo in svg

Wintriss Shadow VI, Руководство пользователя

Пользовательский руководство Wintriss Shadow VI доступен для бесплатной загрузки с manualshive.com. Получите все необходимые инструкции и рекомендации для использования этого продукта. Узнайте, как максимально эффективно использовать Wintriss Shadow VI, загрузив руководство сейчас!

Поделиться
Скачать
background image

Shadow VI User Manual 

1107200 

Installation of Shadow VI-WPC Control Board         Appendix C 

page 121 

 

 

 

 

   

   

 

 

 

 

     

 

       

shadow

 

   VI

WINTRISS LIGHT CURTAIN

MAX RESPONSE TIME <40mS

INPUT POWER

115/230 VAC 1/4 A

50-60Hz MAX 20 VA

SOLID STATE OUTPUTS

MAX 20 mA/24VDC

SEE CONTROLLER BOARD FOR ITEM

& SERIAL NUMBERS

1-800-586-8324

®

 

 

 

 

 

 

 

 

Substitution of
components may
impair operator
safety.

La substitution

d’éléments constitutifs

peut compromettre la

sécurité d l’operateur.

!

WARNING    AVERTISSEMENT

 

 

 
 
 
 

 

 

 

 

 

 

Figure C-1.  Shadow VI - WPC Labels 

"Daily tests" label (left), "Shadow VI" label showing response time (upper right), 
“Warning” label (lower right)  

ATTENTION

CAUTION

Perform these tests daily to make sure
the Light Curtain and the machine's
control system work properly.  Also,
perform these tests after any
modification or maintenance to the
Light Curtain or the machine.
NOTE:  Use an opaque 1 1/4" diameter
test bar for performing the daily tests.
1. Turn on power to the Light Curtain
and the machine.  If the red and green
lights are on at the same time, clear the
Light Curtain to green state by
momentarily interrupting the sensing
field with a test bar.
2. If  your  Light  Curtain  has  a  Floating
Window, shut off the Floating Window
system.  Make sure the Floating
Window indicator light goes off.
3. Interrupt  the  sensing  field  on  the
receiver side by passing the test bar
from the top to the bottom of the
receiver lens cover.  The red light
should come on while the bar is in the
sensing field.
4. Repeat  step  3,  passing  the  bar  from
the top to the bottom of the transmitter
lens cover.  Make sure the red light
comes on when the bar is in the
sensing field.
5. Start the machine and interrupt the
sensing field with the test bar.  The red
indicator light on the receiver should
come on and the machine should
immediately stop. NOTE:  When muting
is used, interrupting the Light Curtain
during the muted portion of the stroke
will NOT stop the machine.
6. Cycle  the  machine  and  make  sure  it
stops at the proper position and that the
machine's braking system is working
properly.  If the machine does not brake
fast enough, adjust the braking system
or increase the Light Curtain's safety
distance.
7. If  the  machine  or  Light  Curtain  fails
any of these tests, DO NOT RUN THE
MACHINE.  Notify the supervisor
immediately.
8. When using the Light Curtain with
mechanical power presses, all OSHA
Safety and Health Standards
(29 CFR 1910.217) must be met.  DO
NOT USE THE LIGHT CURTAIN ON
F U L L   R E V O L U T I O N   C L U T C H
MACHINES.

LIGHT CURTAIN DAILY TESTS

Perform these tests daily to ensure the
Light Curtain and the machine's control
system work properly. These tests
should also be performed after any
modification or maintenance to the
Light Curtain or the machine.

Des essais doivent être effectués
chaque jour pour s'assurer que le
rideau de lumière et le système de
commande de la machine fonctionnent
comme il faut. Ces tests doivent
également être effectués après toute
modification ou tout entretien du rideau
de lumière ou de la machine.

C42254 Rev

 

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

keilhauer Junior Quick Start Manual preview
Junior
Бренд: keilhauer Страницы: 8
Habitat Solution Manual preview
Solution
Бренд: Habitat Страницы: 8
Oak furnitureland COLORADO Assembly Instructions Manual preview
COLORADO
Бренд: Oak furnitureland Страницы: 6
MAGICKWOODS Elements WINDSOR 30312 Installation Instructions Manual preview
WINDSOR 30312
Бренд: MAGICKWOODS Elements Страницы: 6
Zenna Home 9119GY Assembly Instructions Manual preview
9119GY
Бренд: Zenna Home Страницы: 14
Garden Treasures ALQ04110 Manual preview
ALQ04110
Бренд: Garden Treasures Страницы: 18
Sunjoy S-DN121-2-C2 Instruction Manual preview
S-DN121-2-C2
Бренд: Sunjoy Страницы: 9
Newport Integrity VCS Quick Setup Manual preview
Integrity VCS
Бренд: Newport Страницы: 3
GFW LIMA HIGH GLOSS TV UNIT Assembly Instructions Manual preview
LIMA HIGH GLOSS TV UNIT
Бренд: GFW Страницы: 11
Better Homes and Gardens EASTON BH38-084-099-29 Assembly Instructions Manual preview
EASTON BH38-084-099-29
Бренд: Better Homes and Gardens Страницы: 10
Displays2go SMGEOSHNT1 Assembly Instructions preview
SMGEOSHNT1
Бренд: Displays2go Страницы: 5
Kidco G2400 User Manual preview
G2400
Бренд: Kidco Страницы: 14
feather&black Mala 7 Attachment Instructions preview
Mala 7
Бренд: feather&black Страницы: 3
Axor Steel 35002801 Installation Instructions Manual preview
Steel 35002801
Бренд: Axor Страницы: 8
J&J Global Patio Premier 203028 Instruction Manual preview
Patio Premier 203028
Бренд: J&J Global Страницы: 4
Safavieh Furniture DSK5711 Quick Start Manual preview
DSK5711
Бренд: Safavieh Furniture Страницы: 2
Delta Children 080213020620 Assembly Instructions Manual preview
080213020620
Бренд: Delta Children Страницы: 44
Ada Home Décor Walost Wall Shelf Assembly Instructions Manual preview
Walost Wall Shelf
Бренд: Ada Home Décor Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды