Wintriss Shadow VI Скачать руководство пользователя страница 96

Страница: 96 / 159

1107200

Shadow VI User Manual

page 84

Chapter 4

Troubleshooting Shadow VI

Table 4-1. Shadow troubleshooting guide for 1 or 2 sets (cont.)

Control

Description

Transmitte

Receiver

Indicators

DS1 & 2

Action

Chapter ref.

Receiver head is
not getting power.

OR

Transmitter logic
is not getting
power.

Amb Off Red Red

Off

4 Grn

7 Off
8 Grn

1. Unplug receiver connector at receiver.

If DS3 turns ON, receiver is defective.

2. If DS3 stays OFF, reconnect receiver.

Unplug receiver connector at control. If
DS3 turns ON, receiver cable is shorted
and must be replaced.

3. Unplug transmitter connector at transmitter.

If DS4 turns ON, transmitter is defective.

4. If DS4 stays OFF, reconnect trans-

mitter. Unplug transmitter connector at
control. If DS4 Turns ON, transmitter
cable is shorted and must be replaced.

Receiver “green”,
but control box
“red.”

(Scenario 1)

Amb Grn Red Red

Grn

4 Grn

7 Off
8 Grn

1. Check wiring at control box terminal block

(TB2), which goes to receiver.

2. Using a digital voltmeter, measure the

AC voltage between outputs and ground:
Set #1: between pins 4 & 7 and 5 & 7.
Set #2: between pins 11 & 14 and
12 & 14.
Voltage in each case should read between
5.1 and 5.2 volts.

3. If voltage is 0, receiver connector might be

cross-threaded. Unscrew receiver quick-
connect cable and plug back in. Re-
measure the voltage as in step 2.

4. If voltage is still 0, replace cable.
5. If none of the above works, receiver has a

hardware failure. Contact Wintriss Tech
Support to replace receiver.

Receiver “green”,
but control box
“red.”

(Scenario 2)

Amb Grn Red Off 3

Grn

4 Grn

7 Off
8 Grn

1. This indicates a power supply failure.

Contact the factory for assistance.

“Red” = One or both of these LEDs light up red. “Off” = both are off.

Содержание Shadow VI
































































































































































Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды

Wintriss Shadow VI, Руководство пользователя

Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды