Wintriss Shadow VI, Руководство пользователя

Страница: 129 / 159

Shadow VI User Manual 1107200
Shadow VI Panel Mount Appendix B page 117
REMOTE
INTERRUPT
S3
ORG RED BLK/
BLU
BRN GRN YEL SHIELD
TRANSMITTER/RECEIVER CABLE COLOR CODE
D43087 Rev
DS1 DS2
HEAD INTERRUPT INDICATORS
IN 1 SET MODE, BOTH ON,
IN 2 SETS MODE,
DS1 ON = SET 1 RED,
DS2 ON = SET 2 RED
OFF ON
S4
S1
RESET ON
INTERRUPT
FLOATING
WINDOW
STATUS RELAY FOLLOWS
STOP OUTPUTS
POWER UP
RESET
DISABLE
OPTIONS
GRN AMB RED YEL V-OUT
REMOTE INDICATORS
FSD1 FSD2 STAT GND
RELAY OUTPUTS
E-STOP E-STOP
STATUS
SHIPPED WITH FACTORY
INSTALLED JUMPERS
MPCE2
AUX INPUTS
XMTR INT MPCE1 RESET
RECEIVER 1
RECEIVER 2
TRANSMITTER 2
TRANSMITTER 1
1 SET
2 SETS
HEAD SELECTION
JUMPERS
FUSE F1 1/4 A SLO-BLO, INPUT POWER
FUSES F2, F3, F4 4 A SLO-BLO, RELAY OUTPUTS
FOR ASSISTANCE CALL 1-800-586-8324
®
DATA INSTRUMENTS
75 Discovery Way, Acton MA 01720 U.S.A.
DS8
XMTR
ACTIVE
DS6
DS5
INTERNAL
EXT MPCE2 CK
(DE-ENERGISED)
EXT MPCE1 CK
(DE-ENERGISED)
DS7
RESET
ON
INT/EXT
MPCE CK
SELECTION
JUMPERS
J12
J15
J14
1 10
20 11
1 7
8 14
1 7
14
8
TB2
TB3
TB4
Figure B-1. Daily Tests Label (left) and Operator instructions Label (right)
ATTENTION
CAUTION
Perform these tests daily to make sure
the Light Curtain and the machine's
control system work properly. Also,
perform these tests after any
modification or maintenance to the
Light Curtain or the machine.
NOTE: Use an opaque 1 1/4" diameter
test bar for performing the daily tests.
1. Turn on power to the Light Curtain
and the machine. If the red and green
lights are on at the same time, clear the
Light Curtain to green state by
momentarily interrupting the sensing
field with a test bar.
2. If your Light Curtain has a Floating
Window, shut off the Floating Window
system. Make sure the Floating
Window indicator light goes off.
3. Interrupt the sensing field on the
receiver side by passing the test bar
from the top to the bottom of the
receiver lens cover. The red light
should come on while the bar is in the
sensing field.
4. Repeat step 3, passing the bar from
the top to the bottom of the transmitter
lens cover. Make sure the red light
comes on when the bar is in the
sensing field.
5. Start the machine and interrupt the
sensing field with the test bar. The red
indicator light on the receiver should
come on and the machine should
immediately stop. NOTE: When muting
is used, interrupting the Light Curtain
during the muted portion of the stroke
will NOT stop the machine.
6. Cycle the machine and make sure it
stops at the proper position and that the
machine's braking system is working
properly. If the machine does not brake
fast enough, adjust the braking system
or increase the Light Curtain's safety
distance.
7. If the machine or Light Curtain fails
any of these tests, DO NOT RUN THE
MACHINE. Notify the supervisor
immediately.
8. When using the Light Curtain with
mechanical power presses, all OSHA
Safety and Health Standards
(29 CFR 1910.217) must be met. DO
NOT USE THE LIGHT CURTAIN ON
F U L L R E V O L U T I O N C L U T C H
MACHINES.
LIGHT CURTAIN DAILY TESTS
Perform these tests daily to ensure the
Light Curtain and the machine's control
system work properly. These tests
should also be performed after any
modification or maintenance to the
Light Curtain or the machine.
Des essais doivent être effectués
chaque jour pour s'assurer que le
rideau de lumière et le système de
commande de la machine fonctionnent
comme il faut. Ces tests doivent
également être effectués après toute
modification ou tout entretien du rideau
de lumière ou de la machine.
C42254 Rev