Wintriss Shadow VI Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 159

background image

1107200

Shadow VI User Manual

page 18

Chapter 2

Installation and Checkout

Calculating the Safety Distance

DANGER

!

INCORRECT SAFETY DISTANCE

•

Calculate the safety distance carefully according to the instructions below, and mount your

light curtain heads at least this distance from the hazardous area.

•

Mount your light curtain heads at least 7.5” (191 mm) from the hazardous area, regardless

of the calculated safety distance.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

INCORRECT SAFETY DISTANCE DUE TO BLANKING OR FLOATING WINDOWS

•

Read “Chapter 3 – Fixed and Floating Blanking” before calculating the safety distance. This

chapter tells how to modify the safety distance when you use windows.

•

Modify the safety distance calculated with the instructions below, as required.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

INCREASED SAFETY DISTANCE DUE TO BLANKING OR FLOATING WINDOWS

Modify the safety distance between the light curtain and the hazardous area according to the

instructions in this chapter and in Chapter 3, "Floating and Blanking Windows."

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

INCORRECT SAFETY DISTANCE DUE TO LONGER RESPONSE TIME

Determine which model Shadow safety light curtains you have. Use the correct response

time for your model light curtain in your safety distance calculations. Safety depends on your
installing your light curtain at the correct safety distance from the hazardous area.

12” to 24”

30 ms response time

36” to 48”

50 ms response time

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

STOPPING TIME TOO LONG

Use a brake monitor where a Shadow light curtain is used to protect operators whose hands

are routinely exposed to a hazardous area, as required by OSHA 1910.217 (c) (3) (5). A
brake monitor continually checks that the machine’s stopping time does not exceed a
predetermined limit.

Failure to comply with these instructions will result in death or serious injury.

«
...
28
29
30
31
32
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: Oypla GARDEN Страницы: 3

Бренд: ZEITRAUM Страницы: 2

Бренд: Cantoni Страницы: 3

Бренд: Gazebo penguin Страницы: 39

Бренд: Rauch Страницы: 26

Бренд: ricoo Страницы: 2

OBRA SIDEBOARD BZ-1060-20

Бренд: Moe's Страницы: 2

Citterio M 34315XX1

Бренд: Axor Страницы: 12

Alderwood 223126

Бренд: Coaster Страницы: 4

SAFCO Commute 7825-C

Бренд: LDI Страницы: 4

DESIGNlab Checkpoint Ghost Battlestation Gaming Desk CKP4824GD

Бренд: OSP furniture Страницы: 5

Sorrento Chest 4 Drawers 8000042

Бренд: NPD Страницы: 17

ASTON 1500MM OUTDOOR RECTANGULAR TABLE

Бренд: Tusk Страницы: 3

Бренд: Unfinished Furniture of Wilmington Страницы: 5

Бренд: Elite Страницы: 18

Бренд: Kettler Страницы: 32

Бренд: MAJA Möbel Страницы: 12

Бренд: Dorel Home Products Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды