Wintriss Shadow VI Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 159

background image

Shadow VI User Manual

1107200

Installation of Shadow VI-WPC Control Board Appendix C

page 119

Appendix C – Installation of
Shadow VI-WPC Control Board

This appendix explains how to install, wire, and operate the optional Shadow VI-WPC
control board assembly in conjunction with your Wintriss Clutch/Brake Control (WPC).
This control board replaces the standard Shadow VI control box.

The Shadow VI-WPC control board can only be used with Shadow VI Light Curtains (all
sizes) and Wintriss Clutch/Brake Control. It cannot be used with any other press control or
any other model of light curtain.

NOTICE

This appendix explains specific differences when installing the Shadow VI-WPC board.

Refer to Chapter 2 and related illustrations for complete installation information where noted.

If you ordered WPC with the Shadow VI-WPC control board

factory-installed and pre-

mounted,

you can disregard most of the installation sections in this appendix. You need

only to connect the optic heads to the control board and make appropriate settings.

Mounting Dimensions and Required Clearance

WARNING

!

ELECTRIC SHOCK HAZARD

•

Turn off and disconnect power from the Shadow safety light curtain and from the machinery

it is connected to before making any wiring connections. This includes disconnecting power
to the machine control and motor.

•

Remove all fuses and “tag out” per OSHA 1910.147 Control of Hazardous Energy

(Lockout/Tagout).

•

Ensure that installation is performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

Refer to Figure C-2 for mounting dimensions and required clearance information for the
Shadow VI-WPC control board. The Shadow VI-WPC control board comes assembled with
eight standoffs for each mounting hole. Each standoff is size 6-32 and

1/2

" in length.

Recommended screw size is 6-32 x

3/8

". Be careful to protect existing electronics, PC

boards, etc. in the enclosure while drilling and mounting components.

If you are installing this control board inside a standard resolver-based WPC enclosure, we
recommend that you mount it on the right side of the enclosure. If your display is mounted
on the right side, install this board on the door. When mounted on the door, dress the wires
carefully across the hinge. Use a loom to protect the wires from getting caught in the hinge.

«
...
129
130
131
132
133
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: Jason.L Страницы: 2

Бренд: pakoworld Страницы: 4

Бренд: ofichairs Страницы: 2

Бренд: fantastic furniture Страницы: 15

Capitola SEA8031-Q

Бренд: Safavieh Furniture Страницы: 2

Бренд: modway Страницы: 2

STRATFORD CHTSTR6BK

Бренд: GPM Страницы: 6

Бренд: Zest4Leisure Страницы: 3

SIENNA FINISH 963KFSIc

Бренд: Garden Wood Furniture Страницы: 12

T-BENCH 411/78.1950.22

Бренд: dB Страницы: 6

FlexFit Hyken UN59461

Бренд: UNION & SCALE Страницы: 12

IndaMatic EUROPA 2

Бренд: Indaux Страницы: 16

Бренд: overstock Страницы: 12

Бренд: JAB Страницы: 28

Бренд: Nacon Страницы: 8

Бренд: Tee-Zed Страницы: 2

Bun Feet Nightstand

Бренд: Shanty 2 CHIC Страницы: 9

Бренд: SAFAVIEH COUTURE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды