Wintriss Shadow VI Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 159

background image

1107200

Shadow VI User Manual

page 20

Chapter 2

Installation and Checkout

well. For complete information on OSHA regulation 1910.217 and ANSI standard
B11.1-2009, see the Appendix, found at the end of this manual.

Both the ANSI and OSHA formulas are explained below. If you need assistance in
calculating the safety distance, call Wintriss Tech Support.

The OSHA Safety Distance Formula

DANGER

!

INCORRECT SAFETY DISTANCE

•

Calculate the safety distance carefully according to the instructions below, and mount your

light curtain heads at least this distance from the hazardous area.

•

Mount your light curtain heads at least 7.5” (191 mm) from the hazardous area, regardless

of the calculated safety distance.

•

Be sure your value for Ts includes the response times of all devices that react to stop the

press. If your measurement of stop time does not include response time of the press control,
light curtain, and any other devices that react to stop the press, the safety distance will be
too short.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

STOPPING TIME TOO LONG

Use a brake monitor where a Shadow light curtain is used to protect operators whose hands

are routinely exposed to a hazardous area, as required by OSHA 1910.217 (c) (3) (5). A
brake monitor continually checks that the machine’s stopping time does not exceed a
predetermined limit.

Failure to comply with these instructions will result in death or serious injury.

The OSHA safety distance formula as specified in OSHA regulation 1910.217 is explained
below. As noted earlier, Wintriss recommends you use the American National Standards
Institute formula for calculating safety distance because it contains more factors that allow
you to calculate the safety distance more precisely. The ANSI formula is explained in the
next section.

Here is the OSHA safety distance formula as specified in OSHA 1910.217:

Ds = 63 inches/second x Ts
63 inches-per-second is the OSHA-recommended hand-speed constant.

Ds

is OSHA safety distance in inches

Ds = 63 x Ts

T

s

is the stopping time of the press (or other machine) in seconds, measured at approximately

90° of crankshaft rotation (or at maximum velocity).

T

s

must include: all components that are

involved in stopping the press; response time of the press control that activates the brake and
response time of the light curtain (30 ms for 6" through 24" models; 35 ms for 30" through
48" models; 40 ms for the 60" model); plus response time of other devices if also involved in
stopping the press.

«
...
30
31
32
33
34
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: ofichairs Страницы: 2

Бренд: Happy Babies Страницы: 7

Бренд: Safco Страницы: 7

Бренд: Naos Страницы: 4

Бренд: NABBI Страницы: 23

Findley & Myers SB36

Бренд: CABINETS TO GO Страницы: 4

Бренд: YitaHome Страницы: 16

Бренд: DHP Страницы: 25

Бренд: HULALA HOME Страницы: 5

Бренд: RiverRidge Страницы: 20

Бренд: Tresanti Страницы: 12

Бренд: Camaflexi Страницы: 13

Бренд: Gautier Office Страницы: 7

Ziga Zaga DF034120

Бренд: Danze Страницы: 11

Бренд: SUNVILLA Страницы: 16

Бренд: Instant Desks Страницы: 2

Бренд: Habitat Страницы: 16

Бренд: Topcon Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды