Wintriss Shadow VI Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 159

background image

Shadow VI User Manual

1107200

Excerpts from OSHA Regulations and

Appendix A

page 105

ANSI Standards
Daily Tests in French and English

Extracts from ANSI B11.19-2003 8.3

Standards Requirements

Explanatory Information

8.3 Electro-Optical, RF, and area scanning
presence-sensing safeguarding devices

8.3.1 Design and Construction

8.3.1.1

The presence-sensing device shall be

designed and constructed to create a field that
detects the presence of an individual(s).

The presence-sensing device shall not create a
hazard in and of itself.

E8.3.1.1

The device should be designed and

constructed such that it does not present
hazards to individuals from:

sharp edge or pinch point hazards;
radiated light or energy hazards;
electromagnetic interference hazards;
electrical shock hazards.

8.3.1.2

The electro-optical presence-sensing

device shall have a minimum object sensitivity
such that an obstruction of a same or greater
size will always be detected anywhere within its
sensing field, regardless of the plane of
intrusion.

E8.3.1.2

The presence-sensing device should

have a minimum object sensitivity stated by the
supplier. For example, an electro-optical device
may detect an opaque object with a diameter of
32 mm (1-1/4 inch) anywhere in its sensing
field, but allow an obstruction with a diameter of
25 mm (1 inch) to pass undetected at certain
points in the field.

8.3.1.3

The device shall not fail to change its

output state, if not muted, when it detects the
presence of an individual.

E8.3.1.3

Muting may be accomplished by the

device, its interface, auxiliary controls, or the
machine control system. When the device
provides the muting, its output may or may not
change state.

8.3.1.4

Adjustment or configuration of

presence-sensing devices shall be capable of
being supervised by the user.

E8.3.1.4

Methods of meeting this requirement

include, but are not limited to, the use of key
operated controls or controls located under
lockable covers.

Adjustments or configuration can include, but
are not limited to:

muting;
blanking;
power adjustments;
sensing field configuration;
reset functions.

«
...
115
116
117
118
119
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: pakoworld Страницы: 2

Бренд: B&Q Страницы: 4

Бренд: B&Q Страницы: 2

Бренд: ofichairs Страницы: 2

Бренд: Gami Страницы: 3

Бренд: Gami Страницы: 16

Бренд: ofichairs Страницы: 2

Бренд: PAIDI Страницы: 8

Бренд: Gautier Страницы: 12

Бренд: S.R.Smith Страницы: 24

Бренд: FUFU & GAGA Страницы: 14

Бренд: Anzzi Страницы: 8

Warner Trestle Dining Table

Бренд: BROSA Страницы: 4

Queen Headboard 0818

Бренд: Baxton Страницы: 8

Бренд: Enwork Страницы: 10

TOWER UNIT 3 DRAWERS 450mm

Бренд: spaceslide Страницы: 5

Prismo CMBK608FAG

Бренд: Furniture of America Страницы: 10

RISE AND RECLINE CHAIR

Бренд: Comfomatic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды