Wintriss Shadow VI Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 159

background image

Shadow VI User Manual

1107200

Introduction to Shadow VI

Chapter 1

page 1

Safety Light Curtain

Chapter 1 – Introduction to Shadow

®

VI

Safety Light Curtain

Shadow VI is a compact, state-of-the-art, 3-box light curtain which contains transmitter and
receiver optic heads plus a separate control.

Shadow protects personnel working around dangerous machinery. The system signals the
press to stop if a person's hand (or any other part of the body) gets too close to the hazardous
area. However, the invisible light screen does not interfere with normal operation. Unlike
mechanical guards which physically block access to the hazardous area, Shadow safeguards
personnel via this field of invisible infrared light.

DANGER

!

FULL REVOLUTION MECHANICAL POWER PRESSES CANNOT BE STOPPED IN MID-

STROKE

•

DO NOT use Shadow safety light curtains on full-revolution clutched machinery.

•

Use Shadow safety light curtains only on machinery that can be stopped at any point in its

stroke or cycle.

Failure to comply with these instructions will result in death or serious injury.

WARNING

!

IMPROPER INSTALLATION

•

Install and use Shadow safety light curtains according to applicable safety standards.

•

Install presses used with Shadow safety light curtains according to the requirements and

inspection procedures of OSHA regulation 1910.217 and ANSI standard B11.1-2009.

•

Install other machinery or devices according to OSHA regulation 1910.212 for general

machine guarding and any other regulations that apply.

Failure to comply with these instructions could result in death or serious injury.

NOTICE

USE EXCERPTS FROM SAFETY STANDARDS FOR REFERENCE ONLY

Refer to the latest versions of the documents from which Wintriss has provided excerpts for

your convenience. An excerpt from OSHA regulation 1910.217 appears in the appendix of
this manual. Excerpts from the American National Standards Institute (ANSI) standards for
safety devices are also included in Appendix A.

ANSI is a federation of trade and professional organizations which sets standards for the

industry based on a national consensus of manufacturers, scientists, technical and
professional groups.

«
...
11
12
13
14
15
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: XYBIX SYSTEMS Страницы: 29

Бренд: Safco Страницы: 3

Бренд: PAIDI Страницы: 9

Бренд: PAIDI Страницы: 34

Бренд: Happybeds Страницы: 5

Бренд: feather&black Страницы: 4

Бренд: EAST COAST Страницы: 12

Бренд: EAST COAST Страницы: 5

Бренд: EAST COAST Страницы: 10

Бренд: VEDUM Страницы: 6

Бренд: ofichairs Страницы: 2

Бренд: Dancover Страницы: 15

Бренд: µ-Dimension Страницы: 3

Бренд: µ-Dimension Страницы: 3

Бренд: µ-Dimension Страницы: 5

Бренд: µ-Dimension Страницы: 3

JAIME HAYON MEZCLA JH20

Бренд: &Tradition Страницы: 5

Isole NN1A-NN1G

Бренд: &Tradition Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды