Wintriss Shadow VI Скачать руководство пользователя страница 64

Страница: 64 / 159

1107200

Shadow VI User Manual

page 52

Chapter 2

Installation and Checkout

7. Leave a service loop at the control to allow for later adjustment of the conduit. Cut the

wires as necessary. Proceed to the next section "Connecting Stop Circuits to the
Control".

Do not connect wires to AC power source until you are done with all other

installation procedures.

Connecting Stop Circuits to the Control

DANGER

FULL REVOLUTION MECHANICAL POWER PRESSES AND OTHER MACHINES

CANNOT BE STOPPED IN MID-STROKE OR MID-CYCLE

•

DO NOT use Shadow safety light curtains on full-revolution clutched machinery or other

equipment that cannot be stopped at any point in its stroke or cycle.

•

Use Shadow safety light curtains only on machinery that can be stopped at any point in its

stroke or cycle.

Failure to comply with these instructions will result in death or serious injury.

DANGER

PRESS MAY CONTINUE TO MOVE AFTER INTRUSION

•

Ensure that Shadow is wired to the emergency stop circuitry of the press.

•

Ensure that any stop initiated by the light curtain is an immediate stop, one that occurs

immediately after the stop signal is sent to the machinery. If the light curtain is not correctly
wired in this way, the press may continue its stroke after an intrusion is detected.(

Failure to comply with these instructions will result in death or serious injury.

DANGER

STOP CIRCUITS NON-OPERATIVE IN SOME MODES

Wire the light curtain in series with your press control circuit so the stop signal from the light

curtain stops the machine immediately in all modes of operation, including inch.

Failure to comply with these instructions will result in death or serious injury.

WARNING

ELECTRIC SHOCK HAZARD

•

Ensure that the power source is off before you make any wiring connections.

•

Disconnect power from the machinery it is connected to before making any wiring

connections. This includes disconnecting power to the machine control and motor.

•

Ensure that all procedures are performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

Содержание Shadow VI
































































































































































Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды

Wintriss Shadow VI, Руководство пользователя

Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды