Wintriss Shadow VI Скачать руководство пользователя страница 97

Страница: 97 / 159

Shadow VI User Manual

1107200

Troubleshooting Shadow VI

Chapter 4

page 85

External MPCE Monitoring: Checking DS5 and DS6

These LEDs help diagnose problems relating to external MPCE monitoring. If you are using
external MPCE monitoring do the following:

1. Block the light curtain and look at LEDs DS5 and DS6 (see Figure 2-14 for location).

They should both light up orange.

2. If only one lights up, or if neither lights up, check the machine control circuit.

3. Verify that MPCE wiring is correct and check that MPCE jumpers J14 and J15 are both

set for “external.” See Chapter 2.

Table 4-2. Shadow Troubleshooting Guide for 2 Sets

Control

Set

Description

Transmitte

Receiver

Indicators

DS1 & 2

Action

Chapter ref.

#1

#2

Set #1 optic heads
are blocked.

Amb

Red

Grn

Red

1 Red

2 Off

3 Grn

4 Grn

7 Off

8 Grn

1. Make sure a part of the machinery or

other object is not inadvertently
protruding into the light field.

2. Check lens cover(s) for dirt buildup

-

4

#1

#2

Set #2 optic heads
are blocked.

Amb

Grn

Red

1 Off

2 Red

3 Grn

4 Grn

7 Off

8 Grn

and clean if necessary.
3. Check alignment. Realign if necessary.

#1

#2

Sets #1 and #2
optic heads are
both blocked.

Transmitter #1 is
wired with
receiver #2 and
vice versa.

Amb

Red

1 Red

2 Red

3 Grn

4 Grn

7 Off

8 Grn

1. Complete steps 1, 2 and 3, above.
2. If this does not solve the problem, check

to see if transmitter and receiver
connections are reversed. If you cannot
trace the problem, go to the section that
immediately follows this table for
further instructions.

4, 2

#1

#2

Relays are
chattering on
and off.

Amb

Grn

Flicker

betw/

Grn &

Red

1 Off

2 Off

3 Grn

4 Grn

7 Off

8 Grn

1. Optic head jumper setting is incorrect (1

set vs. 2 sets). Check that both
“1 set/2 sets” jumpers at J12 are set at
“2 sets.”

Содержание Shadow VI
































































































































































Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды

Wintriss Shadow VI, Руководство пользователя

Результаты поиска

Содержание Shadow VI

Отзывы:

Похожие инструкции для Shadow VI

Бренды по названию

Популярные бренды