Wintriss Shadow VI Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 159

background image

Shadow VI User Manual

1107200

Excerpts from OSHA Regulations and

Appendix A

page 113

ANSI Standards
Daily Tests in French and English

Daily Tests in English

Perform these tests daily to make sure the light curtain and the machine's control systems
work properly. Also perform these tests after any modification or maintenance to the light
curtain or the machine.

NOTICE

Use an opaque 1¼" diameter test bar for performing the daily tests on the Light Curtain. If

you are using the Floating Window option, enable it and use a 2" diameter test bar to
perform the daily tests.

1. Turn on power to the light curtain and to the machine.

Observe the LEDs at the receiver.

If the red and green lights are on at the same time, clear the light curtain to the green state
by momentarily interrupting the sensing field with a test bar.

2. Interrupt the sensing field on the receiver side by passing the test bar from the top to the

bottom of the receiver lens cover. The red LED on the receiver should come on while the
bar is in the sensing field.

3. Repeat step 2, passing the bar from the top to the bottom of the transmitter lens cover.

Make sure the red LED comes on when the bar is anywhere in the sensing field.

4. Start the machine and interrupt the sensing field with the test bar. The red LED should

come on and the machine should immediately stop.

NOTICE

When muting is used, interrupting the Light Curtain during the MUTED (nonhazardous)

portion of the cycle will NOT stop the machine.

5. Single stroke the machine and make sure it stops at top dead center and that the machine's

braking system is working properly. If the machine does not brake fast enough, adjust
the braking system or increase the light curtain's safety distance.

6. If either the light curtain or the machine fails any of these tests, DO NOT RUN THE

MACHINE. Notify the supervisor immediately.

7. When using the light curtain on mechanical power presses, all OSHA Safety and Health

Standards (29 CFR 1910.217) must be met. DO NOT USE THE LIGHT CURTAIN ON
FULL-REVOLUTION CLUTCH MACHINES.

«
...
123
124
125
126
127
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: Gami Страницы: 5

Бренд: SALICE Страницы: 40

Бренд: tayco Страницы: 20

Бренд: Habitat Страницы: 10

Бренд: Vanico Maronyx Страницы: 16

Бренд: Garden Treasures Страницы: 18

Бренд: Sunjoy Страницы: 9

Бренд: Furniture of America Страницы: 12

Бренд: Furniture of America Страницы: 7

Step Stringer Handrail

Бренд: eDecks Страницы: 8

Бренд: Grammer Страницы: 48

Бренд: IKEA Страницы: 8

VALENCIA 686171

Бренд: Next Страницы: 17

Бренд: Ave Six Страницы: 3

Бренд: Furniture of America Страницы: 13

Бренд: HAMPTON BAY Страницы: 7

Бренд: HAMPTON BAY Страницы: 10

Бренд: JAB Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды