Westlock ICoT 5500 Скачать руководство пользователя страница 189

Страница: 189 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 189 of 206

alarm hysteresis. The directions are reversed for
low limit detection. The hysteresis is also used for
warnings.

Alarm/Warning Limits

Upper Limit Alarm: Upper alarm limit in engineering units.

Upper Limit Warning: Upper warning limit in engineering units.
Lower Limit Warning: Lower warning limit in engineering units.

Lower Limit Alarm: Lower alarm limit in engineering units.

HI_HI_ALM

Unacknowledged Alarms: Unacknowledged alarms.

Status: Status for the upper alarm.

Time Stamp: The time of day when a change in limit stated was

detected that was unreported.

Cause: Cause of the upper alarm.

Alarm Output Value: Output value at the time of the upper alarm.

HI_ALM

Unacknowledged Warnings: Unacknowledged warnings.

Status: Status for the upper warning.

Time Stamp: The time of day when a change in limit stated was

detected that was unreported.

Cause: Cause of the upper warning.

Warning Output Value: Output value at the time of the upper warning.

LO_LO_ALM

Unacknowledged Alarms: Unacknowledged alarms

Status: Status for the lower alarm.

Time Stamp: The time of day when a change in limit stated was

detected that was unreported.

Cause: Cause of the lower alarm.

Alarm Output Value: Output value at the time of the lower alarm.

Simulation

Simulation Value: For commissioning and maintenance reasons, it is

possible to simulate the Read back by defining the
value and the status. That means that the
Transducer Block and the Function Block will be
disconnected.

Status (Simulation Value): Status for the simulate value.

Simulation: Enable or disable the simulation.

OUT_UNIT_TEST

Содержание ICoT 5500















































































































































































































Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды

Westlock ICoT 5500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды