Westlock ICoT 5500 Скачать руководство пользователя страница 175

Страница: 175 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 175 of 206

Disabled State Alarm Sum: Disabled State Alarm Sum.

Batch Information

Batch ID: Identifies certain batch to allow assignment of

equipment-related information (e.g. faults, alarms…)
to the batch.

Batch Unit: Identifies the active Control Recipe Unit Procedure

or the related Unit (e.g. reactor, centrifuge, drier).

Batch Operation: Identifies the active Control Recipe Operation.

Batch Phase: Identifies the active Control Recipe Phase.

Setpoint: Defines the position of the regulation unit within the

travel span (between the OPEN and CLOSED
position) in units of Input Value.

Status (Setpoint): Status of the actual position of the regulating unit

within the travel span (between the OPEN and
CLOSED position) in units of Input Value. Contains
the following states of quality: Good, Uncertain and
Bad.

PV_SCALE

Upper Value: Defines the operational upper range value of the

input value (100%) in engineering units.

Lower Value: Defines the operational lower range value of the

input value (0%) in engineering units.

Unit (Input): Engineering units of the input value.

Decimal Point: The number of digits to the right of the decimal

point.

READBACK

Readback Value: The actual position of the regulating unit within the

travel span (between OPEN and CLOSED position)
in units of Input Value.

Status (Readback Value): Contains the following states of quality: Good,

Uncertain and Bad.

RCAS_IN

RCAS IN: Target setpoint provided by a supervisory host to

the analog control or output block (RCAS mode).

Status (RCAS IN): Contains the flowing states of quality: Good

(Cascade), Uncertain and Bad.

Channels

Содержание ICoT 5500















































































































































































































Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды

Westlock ICoT 5500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды