Westlock ICoT 5500 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 206

background image

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 179 of 206

of the block are used to determine if the block can
achieve the requested target mode. The automatic
modes used in this profile are Auto and RCAS. The
manual modes are LO and Man. In O/S mode, the
normal algorithm is no longer executed.

Actual Mode: Indicates the current mode of operation the block is

able to achieve.

Permitted Mode: Defines the modes which are allowed in this

instance of the block.

Normal Mode: The mode which the block uses during normal

operation conditions.

Alarm Summary

Current State Alarm Sum: The alarm sum of the current alarm state.

Unacknowledged State Alarm

Sum:

The alarm sum of the unacknowledged alarm state.

Unreported Stated Alarm Sum: Unreported State Alarm Sum.

Disabled State Alarm Sum: Disabled State Alarm Sum.

Min. Travel time

Min. Travel Time Close: Time interval from opened to closed positions

registered during the last calibration.

Min. Travel Time Open: Time interval from closed to opened positions

registered during the last calibration.

Linearization Table

Min Number of Coordinates: Informs the minimal number of coordinates

supported by the device.

Max Number of Coordinates: Informs the maximum number of coordinates

supported by the device.

Number of Coordinates: The actual number of coordinates currently stored in

the device. Change this parameter to the intended
number of coordinates before setting up a new
curve.

DEADBAND

Deadband: Valve position dead band in general used as dead

band for the travel alert, setpoint deviation alert,
LCD position filter, close position deviation alert and
full stroke time measurement.

DEVICE_CALIB_DATE

Calibration Date: Date of the device’s last calibration. This value will

change after a successful calibration.

«
...
177
178
179
180
181
...
»

Содержание ICoT 5500















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICoT 5500

Бренд: Power-Genex Страницы: 58

Бренд: EBRO ARMATUREN Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды