manualshive.com logo in svg

Westlock ICoT 5500, Инструкция по установке и эксплуатации

Установочное и руководство по эксплуатации Westlock ICoT 5500 доступно для бесплатного скачивания на нашем сайте. Это подробное руководство содержит важную информацию о продукте, и вы можете скачать его прямо сейчас с manualshive.com. Не упустите возможность быть в курсе со всеми функциями этого продукта.

Поделиться
Скачать
background image

 

WESTLOCK CONTROLS CORPORATION 

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913 

 

 

 

www.westlockcontrols.com

 

 

10/5/2013 

TECH-477/D.W.O. 21424 

   Page 180 of 206 

 
 

LIN_TYPE

 

Flow Type: Set the type of set point characterization curve. The 

following options are available: 

-

 Linear

: the analog output setpoint from the analog output is 

set directly to the servo PID setpoint; 
- 

Equal Percentage

: the analog output setpoint is used as a 

parameter for the equal percentage function to set the servo 
PID setpoint; 
- 

Quick Opening

: the analog output setpoint is used as a 

parameter for the quick opening function to set the servo PID 
setpoint; 
- 

User defined (table):

 the analog output setpoint is 

characterized using a table defined by the user to set the 
servo PID setpoint. (

See the Characterization Curve section to 

get details how to enter this table).

 

RATED_TRAVEL

 

Nominal Valve Stroke/Angle: Nominal stroke of the valve in units of OUT_SCALE.

 

Selfcalibration

 

Selfcalibration: A selection of auto-calibration commands, which are 

executed by pressing the “Execute” button. The 
commands are: 

- No reaction of the field device; 
- Start self-calibration (auto calibration); 
- Reset alarms; 
- Reset internal control loop; 
- Abort current calibration-procedure.

Status (Selfcalibration): Result or status of the calibration procedures. 

 

PID Coefficients

 

Proportional-Action Coefficient 1: Proportional-action coefficient for both moving 

directions. 

Derivative-Action Coefficient 1: Derivative-action coefficient for both moving 

directions. 

Integral-Action Coefficient 1: Integral-action coefficient for both moving directions.

 

SETP_CUTOFF

 

Setpoint Cut-Off CLOSE: Lower level for the setpoint cut-off. The transducer 

setpoint will be forced to zero if the AO.output is 
equal or smaller than this value. 

Setpoint Cut-Off OPEN: Upper level for the setpoint cut-off. The transducer 

setpoint will be forced to 100% if the AO.output is 
equal or greater than this value. 
 

VALVE_TRAVEL

 

Total Valve Travel Accumulated valve travel in nominal duty cycles. 

Limit Total Valve Travel Limit for the “Total Valve Travel” in duty cycles. 

Содержание ICoT 5500















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICoT 5500

Parker LCR Series Product Manual preview
LCR Series
Бренд: Parker Страницы: 39
Vahle APOS Installation Manual preview
APOS
Бренд: Vahle Страницы: 20
Samson 3730-4 Configuration Manual preview
3730-4
Бренд: Samson Страницы: 100
Bürkert 8791 Operating Instructions Manual preview
8791
Бренд: Bürkert Страницы: 186
Ytc YT-400 Installation Manual preview
YT-400
Бренд: Ytc Страницы: 2
Micronix PP-18 Series Reference Manual preview
PP-18 Series
Бренд: Micronix Страницы: 14
Micronix PPS-60 Series Reference Manual preview
PPS-60 Series
Бренд: Micronix Страницы: 40
Heinzmann PANDAROS DC 6-06 Manual preview
PANDAROS DC 6-06
Бренд: Heinzmann Страницы: 96
GEM C67 CleanStar Installation, Operating And Maintenance Instructions For The Installer And The User preview
C67 CleanStar
Бренд: GEM Страницы: 40
Gemu 1436 cPos eco Operating Instructions Manual preview
1436 cPos eco
Бренд: Gemu Страницы: 56
FIAMA P2X T Series Quick Start Manual preview
P2X T Series
Бренд: FIAMA Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды