Westlock ICoT 5500 Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 206

background image

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 184 of 206

- No reaction of the field device;
- ARM;
- Self-calibration;
- Hall sensor gain calibration;
- Low position calibration;
- High position calibration;
- Transducer calibration;
- Servo PID tuning.

Transducer Command State: Current calibration state.

Enable Alert: This parameter can be used to enable the available

alerts separately.

Alert Status: Shows the alerts enable that is ON in the moment.

Reset Counters: This parameter will reset all counters used for alert

or reset each counter separately.

Total Travel Deadband: In units of TRAVEL_COUNT, this parameter will

setup a dead band to assume that the valve is
totally open or totally close to be used by the
TOTAL_TRAVEL_COUNT. Change this value will
change the values of TRAVEL_LIMIT_LOW and
TRAVEL_LIMIT_UP.

Travel Count Unit: Units used to show the TRAVEL_COUNT.

Travel Count: Counter the total valve movement. The unit is

defined in the TRAVEL_COUNT_UNITS.

Travel Count Deadband: The minimum movement to increase the

TRAVEL_COUNT. The unit is defined in the
TRAVEL_COUNT_UNITS.

Travel Count Limit: Travel limit to indicate the TRAVEL_CNTR alert.

The unit is defined in the TRAVEL_COUNT_UNITS.

Internal Temperature Min: Minimum temperature to start the indication of

TEMP_MAX_MIN alert.

Internal Temperature Max: Maximum temperature to start the indication of

TEMP_MAX_MIN alert.

Setpoint Deviation: Maximum valve position deviation from setpoint.

Setpoint Deviation Deadband: Dead band of the maximum valve position deviation

from setpoint.

Setpoint Deviation Timeout: Timeout to start a setpoint deviation alert indication.

POSITION_HI Alert: Highest position to start the POSITION_HI alert

indication. The dead band for this parameter is the
TOTAL_TRAVEL_DB.

POSITION_LO Alert: Smallest position to start the POSITION_LO alert

indication. The dead band for this parameter is the
TOTAL_TRAVEL_DB.

Fault State Value: If the POSITIONING_VALUE status is bad and the

FAULT_STATE_OPTION is set to
FAULT_STATE_VALVE then parameter TRD_SP
will be set to this value.

«
...
182
183
184
185
186
...
»

Содержание ICoT 5500















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICoT 5500

Бренд: Samson Страницы: 2

Optimux HPP5500 Series

Бренд: Trimteck Страницы: 33

Бренд: Ytc Страницы: 25

PS*3**DN series

Бренд: halstrup-walcher Страницы: 35

Бренд: Arc-Zone Страницы: 13

Бренд: Arc-Zone Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды