Westlock ICoT 5500 Скачать руководство пользователя страница 135

Страница: 135 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 135 of 206

9.9.4.2 Function Block Parameters

OUT

Output Value: Process variable in engineering units in AUTO mode. In

MAN and RCAS modes, this is the value specified by the
operator/engineer in LO.

Status (Output): Current status of the Output.

PV_SCALE

Upper Value: Defines the operational upper range value of the input

value (100%) in engineering units.

Lower Value: Defines the operational lower range value of the input

value (0%) in engineering units.

OUT_SCALE

Upper Value: Upper value (Output Signal Range): Upper range value of

the process variable (100%) in engineering units.

Lower Value: Lower Value (Output Signal Range): Lower range value of

the process variable (0%) in engineering units.

Unit (Output): The engineering unit that the output value is reported in.

Decimal Point: Upper value (Output Signal Range): Upper range value of

the process variable (100%) in engineering units.

LIN_TYPE

Flow Type: Set the type of set point characterization curve. The

following options are available:

Linear

: the analog output setpoint from the analog output is set

directly to the servo PID setpoint;
-

Equal Percentage

: the analog output setpoint is used as a

parameter for the equal percentage function to set the servo PID
setpoint;
-

Quick Opening

: the analog output setpoint is used as a parameter

for the quick opening function to set the servo PID setpoint;
-

User defined (table):

the analog output setpoint is characterized

using a table defined by the user to set the servo PID setpoint. (

See

the Characterization Curve section to get details how to enter this
table).

Channel

Channel: The number of the hardware channel that is connected to

this function block. It defines the associated transducer
block.

PV_FTIME

Filter Time Const: This parameter contains the time constant for the rise time

Содержание ICoT 5500















































































































































































































Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды

Westlock ICoT 5500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды