Westlock ICoT 5500 Скачать руководство пользователя страница 95

Страница: 95 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 95 of 206

Valve Manufacturer: Name of the valve manufacturer.

Actuator Manufacturer: Name of the actuator manufacturer.

Valve Type: Type of valve movement (rotary or linear). It has the following

options:

- Rotary moving valve;
- Linear moving valve.

Actuator type: Type of actuator. It has the following options:

- Electro-pneumatic;
- Electric;
- Electro-hydraulic;
- Others.

Actuator action Fail-Safe position for power-loss of the actuator regarding the

valve position. It has the following options:

- Not initialized;
- Opening (100%);
- Closing (0%);
- None (actual position).

Valve Serial Number: Serial number of the valve belonging to the positioner or the

electronic device.

Actuator Serial

Number:

Serial number of the actuator belonging to the positioner or the
electronic device.

9.3.2.6 Calibration

A subdirectory of Parameters/Transducer, it contains a group of parameters that allows
the user to control the calibration functions of the device.

Calibration Date: Date of the device’s last calibration. This value will change

after a successful calibration.

Self-calibration: A selection of auto-calibration commands, which are

executed by pressing the “Execute” button. The

Содержание ICoT 5500















































































































































































































Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды

Westlock ICoT 5500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды