Westlock ICoT 5500 Скачать руководство пользователя страница 90

Страница: 90 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 90 of 206

Save settings

Save the current settings. This will make all current
settings standard.

Auto-Archiving

Automatically saves while capturing new points of a
curve in an external CSV or MS Access file.

Archive current
curves

Save the current curve in an external CSV or MS
Access file.

Archive settings

Save the current settings in an external CSV or MS
Access file

9.3 Calibration and Configuration

9.3.1 Identification

Located under Parameters, at this option is possible to see and modify some
information to describe the device.

TAG:

Physical device tag.

Descriptor:

Text defined by the user to describe the device within an application. It is
a Physical Block parameter with space to store 32 characters.

Message: Also has space to store 32 characters and can be used for any proposal,

especially to describer better the application and the plan where the device
is located.

Installation Date:

User can set the date when the device was installed. It has space
to store 16 characters.

Manufacturer: Identification

of device manufacture. Westlock manufacture ID is 77.

The DTM will show the text “Westlock Controls”.

Device ID:

Westlock device identification. The DTM will show the text “ICoT PA”.

Device Serial Number: Unique serial number

Содержание ICoT 5500















































































































































































































Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды

Westlock ICoT 5500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ICoT 5500

Отзывы:

Похожие инструкции для ICoT 5500

Бренды по названию

Популярные бренды