Westlock ICoT 5500 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 206

background image

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 89 of 206

Holding down the
Right mouse button
above the scale,
drag the pointer
according to the
axis to change the
scale maximum
value.

Holding down Left
and Right mouse
buttons above the
scale, drag the
pointer according
to the axis to
change the scale's
minimum and
maximum values
simultaneously.

9.2.5.2 Buttons and Marks

Some graphs and charts may present some functions accessible by the buttons below:

Update measurement
ranges and units

Updates all measurements ranges and units used in the
graph.

Capture curves

Font enlarge

Increases the font size of all texts in the graph.

Font reduce

Decreases the font size of all texts in the graph.

Scale width enlarge

Increases the width of the left and right sides of the
graph.

Scale width reduce

Decreases the width of the left and right sides of the
graph.

Display tooltips

Enable or disable tooltips when hovering over content.

Display ruler

Allow scale
positioning

Enable or disable positioning using the mouse pointer of
the scales from the graph. If enabled, simply drag the
selected scale to the new position.

Delete curves

Clear the displayed curve from the graph.

«
...
87
88
89
90
91
...
»

Содержание ICoT 5500















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICoT 5500

Бренд: VBOX Страницы: 11

Бренд: halstrup-walcher Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды