Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 194

background image

wc_si000836gb_FM10.fm

16

Rammer

Safety Information

Replacing
parts and
labels

■

Replace worn or damaged components.

■

Replace all missing and hard-to-read labels.

■

When replacing electrical components, use components that are identical in
rating and performance to the original components.

■

When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

■

Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

■

Keep the labels legible.

When cleaning the machine:

■

Do not clean the machine while it is running.

■

Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.

Personal
Protective
Equipment
(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:

■

Close-fitting work clothes that do not hinder movement

■

Safety glasses with side shields

■

Hearing protection

■

Safety-toed footwear

In addition, before servicing or maintaining the machine:

■

Tie back long hair.

■

Remove all jewelry (including rings).

Safe service
practices

■

Do not alter engine speeds. Run the engine only at speeds specified in

Technical Data

.

■

Do not operate the machine without an air cleaner.

■

Disconnect the spark plug before servicing to avoid accidental start-up.

■

Do not crank a flooded engine with the spark plug removed. Fuel trapped in the
cylinder will squirt out the spark plug opening.

■

Do not test for spark if the engine is flooded or the smell of gasoline is present.
A stray spark could ignite the fumes.

«
...
14
15
16
17
18
...
»

Содержание BS 50-4s, BS 50-4As



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BS 50-4s, BS 50-4As

Бренд: Greenlee Страницы: 10

Бренд: MASTERPAC Страницы: 22

Бренд: MASTERPAC Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды