Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 48

Страница: 48 / 194

wc_tx004029gb_FM10.fm

Rammer

Disassembly and Reassembly

4.5

Removing the Ramming Shoe—BS50

Requirements

■

Torque wrench

■

Lifting device capable of lifting the machine

■

See chapter

Technical Data

for weights

Procedure

Perform the procedure below to remove the ramming shoe.

1. Using the lifting device, support the machine in a vertical position.

2. Remove the six nuts

(a)

and the lock washers

(b)

3. Remove the lifting handle

(c)

and the two spacers

(d)

This procedure continues on the next page.

To view an animation of this procedure, internet access
is needed.
To view the animation, click on the video icon or scan
the QR code with a smart phone.

WARNING

Crushing hazard. The machine may fall if not properly suspended during ramming
shoe replacement.

►

Only use appropriate lifting devices and techniques when lifting the machine.

wc_gr012676

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды