Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 124

Страница: 124 / 194

wc_tx004029gb_FM10.fm

124

Rammer

Disassembly and Reassembly

4.32

Installing the Upper Machinery

Requirements

■

Punch

■

New end plugs

■

New O-ring

■

Loctite® 243

■

Two wood blocks 2” x 4” x 8” (5cm x 10cm x 20cm)

Procedure

Perform the procedure below to install the upper machinery.

1. Install a new O-ring

(g)

2. Place the two wood blocks

and

on the guide cylinder.

3. With the aid of an assistant, position the upper machinery on the two wood

blocks and align the crankcase connecting rod

(h)

with the ram

(c)

Note: Use new end plugs (e) whenever the piston pin (f) has been removed.

4. Using a hammer and punch, drive in the piston pin

(f)

and new end plugs

(e)

5. Remove the two wood blocks

and

This procedure continues on the next page.

To view an animation of this procedure, internet access
is needed.
To view the animation, click on the video icon or scan
the QR code with a smart phone.

wc_gr012853

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды