Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 29

Страница: 29 / 194

wc_tx004063gb_FM10.fm

Rammer

Troubleshooting

3.1

Diagnosing Starting Issues

Tools required

All procedures can be accomplished with the following tools:

■

Spark tester (part number 5000078836)

■

Multimeter

■

General hand tools (ratchet set, screwdrivers, etc.)

Where to start

To determine where to start:

1. Determine the issue from the chart below. Complete all tasks in the order listed.

Engine doesn’t start

See topics

No.

1. Check level of fuel in tank.

—

2. Check the fuel flow.

Checking the Fuel Flow

3.3

3. Check the ignition module/spark

plug.

Testing the Ignition Module and
Checking the Spark Plug

3.4

4. Check the stop switch.

Checking the Stop Switch

3.5

5. Check cylinder/piston for leakage.

Conducting a Leak-Down Test

3.6

6. Check the ignition wiring.

Checking the Ignition Wiring

3.7

Engine starts, but does not come up
to full speed

See topics

No.

1. Check the fuel flow.

Checking the Fuel Flow

3.3

2. Check the fuel cap.

—

3. Check carburetor for dirt.

See engine repair manual

—

4. Check engine compression.

Checking Engine Compression

3.8

Engine starts, but shuts down after
approximately 25 seconds

See topics

No.

1. Test oil float switch.

Testing the Float Switch

4.47

2. Check ignition module.

Checking the Ignition Module

3.4

Engine starts and runs to full speed,
then slows down like it may stop,
then picks up speed again.

See topics

No.

1. Check the spark plug

Checking the Spark Plug

3.4

Engine stops after running for
approximately 45 minutes

See topics

No.

1. Check the fuel flow.

Checking the Fuel Flow

3.3

2. Check the spark plug.

Checking the Spark Plug

3.4

3. Check fuel cap for proper venting.

—

4. Check for vapor lock.

Checking for Vapor Lock

3.9

5. Purge the oil lines.

Purging the Oil Lines

3.10

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды