Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 66

Страница: 66 / 194

wc_tx004029gb_FM10.fm

Rammer

Disassembly and Reassembly

4.15

Removing the Bellows

Requirements

■

Punch

■

Rubber mallet

■

Two wood blocks 2” x 4” x 8” (5cm x 10cm x 20cm)

Background

The bellows should be warm. If possible, place machine in sunshine or near heat
source to warm the bellows.

Procedure

Perform the procedure below to remove the bellows.

1. Drain the ramming system oil into an approved container.

Note: Dispose of oil in accordance with local environmental regulations.

2. Remove the four screws

(a)

and washers that fasten the ramming system to the

crankcase.

3. With the aid of an assistant, roll the crankcase and place a wood block

(b)

between the crankcase and the ramming system.

4. With the aid of an assistant, roll the crankcase the opposite direction and place

a second wood block

(d)

between the crankcase and the ramming system. This

provides access to the crankcase connecting rod and ram

(c)

This procedure continues on the next page.

To view an animation of this procedure, internet access
is needed.
To view the animation, click on the video icon or scan
the QR code with a smart phone.

wc_gr012686

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды