Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 31

Страница: 31 / 194

wc_tx004063gb_FM10.fm

Rammer

Troubleshooting

3.3

Checking the Fuel Flow

Requirements

■

Fuel in tank

■

Fuel valve open (throttle out of stop position)

Procedure

Perform the procedure below to check the fuel flow.

1. Open the fuel valve by setting the throttle to any position besides the STOP

position.

2. Press the purge bulb several times and look for fuel flow through the fuel hoses.

Is there fuel flow in the fuel hoses?

3. Locate the in-line fuel filter

(a)

4. Cut the fuel hose

(b)

as close to the nipple as possible.

This procedure continues on the next page.

WARNING

Fire hazard. Fuel is flammable and may ignite.

►

Keep all sources of ignition far away while performing this procedure.

►

Clean up spilled fuel immediately.

Yes ____

No ____

Clean, adjust, or replace the spark plug and try starting again.

If spark plug is OK, see topic

Testing the Ignition Module and

Checking the Spark.

Continue with step 3.

wc_gr012828

2-Stroke

4-Stroke

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды