Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 11

Страница: 11 / 194

wc_si000836gb_FM10.fm

Rammer

Safety Information

1.1

Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION,

NOTICE,

and NOTE

signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.

NOTICE:

Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

►

Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.

►

To avoid death or serious injury from this type of hazard, obey all safety mes-
sages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.

►

To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.

►

To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды