Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 157

Страница: 157 / 194

wc_tx004029gb_FM10.fm

157

Rammer

Disassembly and Reassembly

Continued from the previous page.

1. Install the bottom spring set

(g)

into the spring cylinder.

2. Place a new gasket

(f)

onto the spring cylinder.

3. Align the three holes in the spring box tool

(a)

with the three holes in the spring

system cover

(e)

4. Insert the three spring box screws

(c)

through the selected holes in the spring

box tool and through the holes in the spring system cover.

5. Turn the spring box screws

(c)

into the spring cylinder until they bottom out.

6. Turn the threaded rod

(d)

until the spring system cover makes contact with the

spring cylinder.

7. Apply Loctite® 243 to all the screws used to fasten the spring system cover to

the spring cylinder.

8. Install the screws

(b)

that hold the spring system cover to the spring cylinder.

Torque the screws to 24 Nm (18 ft.lbs.).

This procedure continues on the next page.

wc_gr012887

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды