Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 94

Страница: 94 / 194

wc_tx004029gb_FM10.fm

Rammer

Disassembly and Reassembly

4.23

Removing the Carburetor—Honda

Requirements

■

Approved container for drained fuel

■

Plastic sheet to protect work surface

Procedure

Perform the procedure below to remove the carburetor.

1. Drain the fuel tank contents into an approved container.

Note: Dispose of fuel in accordance with local environmental regulations.

2. Remove any wire ties attached to the carburetor guard

(b)

3. Remove the screw

(a)

and the nut fastening the fuel filter and the clip to the

carburetor guard

(b)

4. Remove the four screws

(c)

and the carburetor guard

(b)

5. Loosen the hose clamp

(e)

and disconnect the air tube

(d)

This procedure continues on the next page.

WARNING

Fire hazard. Fuel is flammable and may ignite.

►

Keep all sources of ignition far away while performing this procedure.

►

Clean up spilled fuel immediately.

wc_gr012682

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды