Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 39

Страница: 39 / 194

wc_tx004063gb_FM10.fm

Rammer

Troubleshooting

3.9

Checking for Vapor Lock

Requirements

■

Fresh, non-oxygenated fuel

■

New fuel filter if applicable

Background

Loading conditions, fuel blend, and ambient temperature all add to the chances of
a vapor lock condition. If the engine runs for approximately 45 minutes and then
stops, there may be a vapor lock condition.

Checking
procedure

Perform the procedure below to check for vapor lock.

1. Check the fuel level in the fuel tank. Fill the fuel tank if necessary.

2. Check the purge bulb

(a)

. If there is no fuel in the purge bulb, a vapor lock

condition may exist.

3. Check for air bubbles in the return fuel hose

(b)

. If there are air bubbles present,

a vapor lock condition may exist.

Solution

To rectify a vapor lock condition:

►

Allow the machine to cool.

►

Check the fuel tank cap. The cap needs to vent. If it is screwed on too tightly,
venting will be inhibited.

►

Replace the fuel with fresh, non-oxygenated fuel.

►

Check the fuel filters. Replace the fuel filters if necessary.

►

Check the fuel hoses for kinks and leaks. Replace the fuel hoses if necessary.

wc_gr013200

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды