Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 129

Страница: 129 / 194

wc_tx004029gb_FM10.fm

129

Rammer

Disassembly and Reassembly

4.34

Installing the Crankcase

Requirements

■

New O-ring

■

Loctite® 243

■

Large diameter retaining ring pliers

■

Hydraulic press

Procedure

Perform the procedure below to install the crankcase.

1. If the needle bearing

(h)

was removed, press a new needle bearing into the

front crankcase cover

(b)

until the outer race is flush with the flange surface.

2. Place the large retaining ring

(m)

over the shaft of the crank gear

(c)

3. Press the ball bearing

(k)

onto the shaft of the crank gear and re-install the small

retaining ring

(j)

4. Press the ball bearing

(n)

into the connecting rod

(d)

5. Press the connecting rod assembly onto the crank gear

(c)

and secure it in

place with the small retaining ring

(u)

This procedure continues on the next page.

To view an animation of this procedure, internet access
is needed.
To view the animation, click on the video icon or scan
the QR code with a smart phone.

wc_gr012876

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды