Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 47

Страница: 47 / 194

wc_tx004029gb_FM10.fm

Rammer

Disassembly and Reassembly

Continued from the previous page.

5. Tip the rammer so that it is perpendicular with the ground to check oil level.

The oil is at the correct level when the oil fills 1/2 to 3/4 of the sight glass.

6. Once the correct oil level is achieved, tip the rammer forward and secure the

rammer.

7. Remove the sight glass, clean the threads, and wrap the threads with Teflon®

tape.

8. Re-install the sight glass and torque to 9 Nm (6ft. lbs.).

Result

The ramming system oil has now been refilled.

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды