Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 32

Страница: 32 / 194

wc_tx004063gb_FM10.fm

Rammer

Troubleshooting

Continued from the previous page.

Does fuel flow from the fuel hose (b)?

5. Locate the fuel hose

(c)

6. Cut fuel hose

(c)

near the nipple of the fuel valve

(d)

. Reference step 4.

Does fuel flow from fuel hose (c)?

7. Remove the in-tank fuel filter. See topic

Removing the Fuel Tank

8. Clean or replace the in-tank fuel filter.

Result

The fuel flow has now been checked.

Yes ____

No ____

Replace the in-line fuel filter.

Remove the stub of hose from the in-line

fuel filter and reconnect the fuel hose

(b)

Continue with step 5.

Yes ____

No ____

Replace the fuel valve.

Remove the stub of hose from the fuel

valve and reconnect the fuel hose

(c)

Continue with step 7.

wc_gr012829

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды