Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 159

Страница: 159 / 194

wc_tx004029gb_FM10.fm

159

Rammer

Disassembly and Reassembly

4.45

Removing the Upper Spring Set

Requirements

■

Drift pin

■

Rubber mallet

■

Impact bushing puller P/N 5000116816

■

Ramming shoe removed

■

Spring system cover removed

■

Lower springs removed

Procedure

Perform the procedure below to remove the upper spring set.

1. Loosen the nut

(d)

on the impact bushing puller to allow the yoke

(c)

to set on

the flange surface of the rammer, and the jaws to reach the bottom of the impact
bushing.

2. Push the jaws

(a)

of the impact bushing puller over the impact bushing

(b)

until it

seats at the bottom of the impact bushing.

3. Once the jaws are seated on the impact bushing, tighten the two wing nuts on

the jaws holding them in place.

This procedure continues on the next page.

To view an animation of this procedure, internet access
is needed.
To view the animation, click on the video icon or scan
the QR code with a smart phone.

wc_gr012843

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды