Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 36

Страница: 36 / 194

wc_tx004063gb_FM10.fm

Rammer

Troubleshooting

3.6

Conducting a Leak-Down Test

Requirements

■

Leak down tester

■

Torque wrench

Procedure

Perform the procedure below to conduct a leak-down test.

1. Remove the spark plug

(a)

2. Set the piston at TDC using the starter rope.

3. Connect the leak-down tester

(b)

to the engine at the spark plug hole.

4. Set the regulator of the air supply to 100 psi. Test the engine leak down using

the instruction of the leak-down tester.

Does the engine hold the pressure?

Result

The engine air leakage has now been checked.

Yes ____

No ____

The air leakage is OK.

Re-install the spark plug. Torque the spark

plug to 35–41 Nm (25.8–30.2 ft.lbs.).

There is too much air leakage.

Rebuild the engine.

wc_gr013050

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды