Wacker Neuson BS 50-4s, BS 50-4As Скачать руководство пользователя страница 98

Страница: 98 / 194

wc_tx004029gb_FM10.fm

Rammer

Disassembly and Reassembly

4.24

Installing the Carburetor—Honda

Requirements

■

Torque wrench

■

Plastic sheet to protect work surface

Procedure

Perform the procedure below to install the carburetor.

1. Assemble the carburetor

(q)

as needed.

2. Install the five gaskets

(s)

(t)

(u)

(w)

, and

(y)

, one plate

(v)

, and one insulator

(x)

to the two stud bolts

(o)

3. Install the carburetor

(q)

the gasket

(r)

, and the elbow

(p)

, to the two stud bolts

(o)

4. Fasten using two nuts

(n)

This procedure continues on the next page.

WARNING

Fire hazard. Fuel is flammable and may ignite.

►

Keep all sources of ignition far away while performing this procedure.

►

Clean up spilled fuel immediately.

wc_gr012685

Содержание BS 50-4s, BS 50-4As



































































































































































































Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды

Wacker Neuson BS 50-4s, BS 50-4As, Руководство по ремонту

Результаты поиска

Содержание BS 50-4s, BS 50-4As

Отзывы:

Похожие инструкции для BS 50-4s, BS 50-4As

Бренды по названию

Популярные бренды