TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 95

Страница: 95 / 154

1st digit = 0:

Input Phase Loss protection function ineﬀective.

1st digit = 1:

Input Phase Loss protection function eﬀective.

•

2nd digit

(Output Phase Loss Protection, OPL)

The output phase loss protection function is disabled while the AC drive is stopped, during DC

injection braking, or when AC drive output current ≤ 30% of AC drive rated output current.

The eﬀectiveness or ineﬀectiveness of output phase loss protection function can also be

selected by the 2nd digit of Sn-13.

2nd digit = 0:

Output Phase Loss protection function ineﬀective.

2nd digit = 1:

Output Phase Loss protection function eﬀective

• 3rd digit

(Heat Sink Cooling Fan ON/OFF Control)

3rd digit = 0:

AC drive heat sink cooling fan runs while the drive power is ON.

3rd digit = 1:

AC drive heat sink cooling fan runs only while the heat sink temperature is

higher than 50 . ˚C

(14) Protective Characteristics Selection 5 (Sn-14)

•

1st digit (

motor protection)

1st digit = 0:

Electronic thermal motor protection is enabled.

1st digit = 1:

Electronic thermal motor protection is disabled.

•

2nd digit

(selection of electronic thermal characteristics)

2nd digit = 0:

Electronic thermal characteristics are in accordance with reduced torque

motor (standard motor).

2nd digit = 1:

Electronic thermal characteristics are in accordance with constant torque

motor (special motor).

•

3rd digit

(electronic thermal time constant)

3rd digit = 0:

Used for standard motors or special motors (standard-time ratings, 8 minutes)

3rd digit = 1:

Used for motors other than the above (short-time ratings, 5 minutes)

• The electronic thermal overload function monitors motor temperature, based on the

AC drive output current and time, to protect the motor from overheating. When

electronic thermal overload relay is enabled, an “OL1” error occurs, shutting oﬀ the

AC drive output and preventing excessive overheating in the motor.

• When operating with one AC drive connected to a single motor, an external thermal relay is

not needed. When operating several motors with one AC drive, install a thermal relay on

each motor. In this case, set constant Sn-14=XXX1.

•

4th digit

(Not used)

2-45

PA 7300

PART II: OPERATION MANUAL

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды