TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 63

Страница: 63 / 154

(1) Input voltage (Cn-01)

• Set AC Drive input voltage. (In units of 0.1V).

(2) V/f constant (Cn-02 to Cn-08)

• Set AC drive output frequency/voltage characteristics (V/f characteristics.)

(a) Changing V/f characteristics

Sn-02 = 0 to 3 : V/f characteristics are determined by set value. Settings of CN-02

to Cn-08 cannot be changed.

Sn-02 = 4 :

Any V/f characteristic can be obtained by the set values of constants

Cn-02 ~ Cn-08

(b) Voltage values (Cn-03, Cn-06, Cn-08) displayed on the LCD operator depend on the set value

of Sn-02 (V/f selection)

The set value is displayed.

(d) When V/F characteristics are a straight line, the same value as Cn-07 is set in Cn-05.

The set value of Cn-06 is disregarded.

Notes:

1. The maximum output voltage is limited by the input voltage.

2. When the set values of Cn-02 to Cn-08 do not satisfy the conditionas stated above, a setting error occurs

and an Invalid V/F OPE10 alarm is displayed.

The set value is checked at power ON and switching from PRG mode to DRIVE mode.

MAX

.≥ F

> F

≥ F

Min.

(3) Motor rated current (Cn-09)

• Set motor rated current by the electronic thermal function in units of 0.1 A for motor

overload protection. The range of setting is 10% to 200% of AC drive rated current.

When the 1st digit of Sn-14 is set to 1, the electronic thermal function is disabled and the

motor is not protected from overheating due to overload.

(4)

DC injection braking starting frequency (Cn-10)

• Set a frequency for starting DC braking during deceleration to stop in units of 0.1 Hz.

When a set value is not greater than Cn-07 (minimum output frequency), DC braking is

started at the minimum output frequency.

2-13

PA 7300

PART II: OPERATION MANUAL

0 F

Min

. F

Max

(Cn-07) (Cn-05) (Cn-04) (Cn-02)

Max

(Cn-03)

(Cn-06)

Min

(Cn-08)

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды