TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 11

Страница: 11 / 154

GENERAL

1.1 SAFE OPERATION NOTES

Read this installation manual thoroughly before installation, operation, maintenance, or inspection of

the apparatus. Only authorized personnel should be permitted to perform maintenance, inspections or

parts replacement.

In this manual, notes for safe operation are classiﬁed as:

“WARNING” or “CAUTION”.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury to personnel.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury to personnel and damage to

equipment. It may also be used to alert against unsafe practices.

This AC drive has been placed through demanding tests at the factory before shipment. After unpacking,

check for the following:

1. Verify that part numbers on the shipping carton and unit match the purchase order sheet and/or packing list.

2. Do not install or operate any AC drive which is damaged or missing parts.

3. Do not install or operate any AC drive which has no QC marking.

Contact your local distributor or TECO representative if any of the above have been found.

1.2 PRODUCT CHANGES

TECO-Westinghouse reserves the right to discontinue or make modiﬁcations to the design of its products

without prior notice, and holds no obligation to make modiﬁcations to products sold previously.

TECO-Westinghouse also holds no liability for losses of any kind which may result from this action.

1-1

PA 7300

PART I: INSTALLATION MANUAL

WARNING

CAUTION

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды