TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 114

Страница: 114 / 154

25. Pump Operation Mode Selection (Sn-30)

• The 1-8 PID Relay option card application parameter. Set PA-PID card ineﬀective (Sn-30=0)

when the 1-8 PID Relay card is not installed. Please refer to “PA-PID instruction manual”.

• Sn-30 = 0:

1-8 PID Relay card is ineﬀective.

Sn-30 = 1:

Fixed AC drive mode stops all the pumps by ﬁrst-run-last-stop sequence. i.e.

Only one of the pumps is driven by AC drive, the others are run with the ac

power source. Take the ﬁrst run pump last stop sequence to stop all the

pumps. This operation mode is better when diﬀerent motor HP/KW ratings

are used.

Sn-30 = 2:

Fixed AC drive mode stops the pump driven by the AC drive only. i.e.

When the AC drive outputs the stop signal, only the inverter driven pump

is stopped.

Sn-30 = 3:

Fixed AC mode, stops all the pumps by ﬁrst-run-ﬁrst-stop sequence. i.e.

the ﬁrst-run (the motor running for the longest time) -ﬁrst-stop sequence

is adapted to stop the motors and keeps the pumps at almost the same duty.

This operation mode is better when using the same motor HP/KW ratings.

Sn-30 = 4:

Cycled AC drive mode, stops all the pumps by ﬁrst-run-ﬁrst-stop

sequence. (i.e. Except for the auxiliary pumps, all the pumps are controlled by

AC drive, and take the ﬁrst-run-ﬁrst-stop sequence to stop all the pumps).

Sn-30 = 5:

Cycled AC drive mode; stops the inverter-driven pumps only.

• Fixed AC drive mode and Cycled AC drive mode connection examples:

(a) Fixed AC Drive mode

(b) Cycled AC Drive mode

Fig. 13 Pump Operation mode

26. 1-8 PID Card Relay 2 Control (Sn-31)

27. 1-8 PID Card Relay 3 Control (Sn-32)

28. 1-8 PID Card Relay 4 Control (Sn-33)

2-64

PA 7300

PART II: OPERATION MANUAL

INV

MC0(RY1)

MC1(RY2)

MC2(RY3)

MC3(RY4)

MC4(RY5)

MC5(RY6)

MC6(RY7)

MC7(RY8)

3
power
source

INV

MC0(RY1)

MC2(RY3)

MC4(RY5)

MC6(RY7)

MC1(RY2)

MC3(RY4)

MC5(RY6)

MC7(RY8)

3
power
source

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды