TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 57

Страница: 57 / 154

(19) Sleep/Wake Delay Time (Bn-19)

• This parameter is eﬀective only when PID mode is active (Sn-19=09)

• This parameter enables the AC drive to stop and start running the motor if the load on

the motor is minimal.

• Sleep / Wake time in Bn-19 starts when the output frequency (f

out

) drops below the frequency set

in Bn-18 or when the frequency command (f

CMD

) exceeds the wake frequency (Bn-20)

• During the sleep mode (i.e. when the output frequency ≤Bn-18), when the time set in the timer

has expired, the AC drive will ramp down the motor to stop. During the wake mode (i.e. when

the frequency command ≥Bn-20), when the time set in the timer has expired, the AC drive will

accelerate to frequency command. If the output frequency rises above the frequency set in

Bn-18, or the frequency command drops below the set value in Bn-20, the timer is reset.

(20) PID Wake Frequency

(Bn-20)

• This parameter is eﬀective only when PID mode is active (Sn-19=09)

• Frequency level for deactivation of sleep function. When the frequency command (f

CMD

)

exceeds the wake frequency and after the time delay set in Bn-19, the AC drive restarts

the motor.

• While the AC drive has stopped the motor in sleep mode, the PID control function is still

working. When the frequency command rises above the wake frequency in Bn-20 and

after the time delay set in Bn-19, the AC drive will restart the motor and the output frequency

will ramp up to the frequency command.

2-7

PA 7300

PART II: OPERATION MANUAL

Figure 11-(c) Sleep Wake function in PID Mode

Figure 11-(d) Sleep/Wake Operation Mode

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды