TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 126

Страница: 126 / 154

3-4

PA 7300

PART II: OPERATION MANUAL

FAULT CONTACT

OUTPUT

ERROR CAUSES

ACTION TO BE TAKEN

Operation

Parameter setting error

• One of the AC Drive input phases are lost

• 3 phase power source is unbalanced.

• Check the AC Drive input power supply wiring.

Operation

• The main circuit smoothing capacitors have deteriorated.

• Check the capacitors.

• Improper input phase loss detection level (Cn-61) setting

• Check the setting of Cn-61.

Operation

• One of the AC Drive output phases are lost

• Check the wiring between AC Drive and motor.

• DCCT fault.

• Replace the DCCT.

Operation

• Motor load current is too large.

• Check the motor load current.

• The eﬀective cooling of motor is not suﬃcient.

• Check the motor eﬀective cooling.

Operation

• RS-485 communication option card fault

• Excess vibration or shock

• Turn oﬀ power, then turn on again. If error is

• External noise

persistent, replace the option card.

Operation

• The RS-485 communication protocols setting AC Drive

• Check the setting in Sn-24 and option card.

(Sn-24) and option card are inconsistent.

Operation

• PA-P card fault

• Turn oﬀ power, then turn on again. If error is

persistent, replace the option card

Operation

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды